Total Pageviews

Showing posts with label Swarovski Crystal. Show all posts
Showing posts with label Swarovski Crystal. Show all posts

Monday, August 29, 2016

Make It Monday DIY: Whimsical Memory Wire Ring Featuring Charms Made With Swarovski® Crystals

On Saturday, I posted a tutorial of a super cute ear cuff with a peacock feather charm.  Today, I am showing you how to make a adorable beaded memory wire ring using more of charms made with Swarovski® Crystals from Cousin Corporation of America available exclusively from Michael's Craft Stores.  There are links below for my fellow ambassadors' projects using these lovely little charms as well.

This ring is fun and easy to make, and it will become your favorite go to ring in no time.




Materials:
Ring Sized Memory Wire
11/0 Seed Beads (Yeah....tiny ones)
1 Sunshine Bumble Bee Charm (or charm of choice)

Tools:
Memory Wire Cutters
Memory Wire Finishing Pliers (I HIGHLY recommend these over round nose for this project)

Skill Level: Beginner

Craft Time: About 45 minutes


Instructions:
Separate three to four rounds of memory wire and cut in line with the end of the wire.  Using the smallest part of the Memory Wire Finishing Pliers, form a loop at one of the ends of the memory wire.
 
Bead your wire in any pattern or solid color of your choice.  I used TOHO Galvanized Silver,  Starlight Galvanized Gold and Hematite for my Bee ring. Bead up until you have about a 1/4 of an inch of wire left and form your end loop the same as you did your beginning loop.






Attach your charm with the clip onto either one or both of the loops.  If you want a more adjustable ring, clip the charm on only one of the loops.


Enjoy your new fun ring!








LINKS:
DIY Wine Charms by Rebecca Grafton
DIY Gift Packaging by Rebecca Grafton
DIY Skull Necklace by Jennifer Priest
DIY Back To School Ideas by Jennifer Priest
DIY Ideas by Lisa Crone
DIY Handmade Card by Rachel Nielsen
DIY Bookmarks by Rachel Nielsen
DIY Dangle Ear Cuff by Shelly Owen



Saturday, August 27, 2016

Weekend Whimsy DIY - Wire Ear Cuff the Interchangeable Charms

It's been some time since I have done a blog post. So, why not do a tutorial?

Today's tutorial is a super cute and trendy, easy to make spiral wire ear cuff with an adorable interchangeable charm.  These charms are made with Swarovksi® crystals and are available exclusively from Michael's Craft Stores.  These little beauties are put out by Cousin Corporation of America.  The charms come in a variety of shapes such as bumble bees, flowers, hearts, owl, and even birthstone colors.

Cousin Corporation sent the us ambassadors a few of these charms to play around with. At the end of this tutorial are links to the other projects done by my fellow ambassadors.


I chose this lovely peacock feather charm to start with.


Materials:
1 Paradise Shine Peacock Feather Charm
20 gauge wire

Tools:
Ruler with both standard and metric measurements
Round Nose Pliers
Bail Making Pliers (optional)
Eye Protection

Skill Level: Beginner

Instructions:

Cut a 4 inch section of wire.  Lay the wire against the metric side of the ruler, and measure 4 cm from one end of the wire. Bend the wire back over itself using round nose pliers.

Measure 3 cm from the bend and and then fold the other end of the wire over forming a "Z" shape.




Using your round nose pliers form a loose spiral on each tail end of the wire.


















Wrap your form around the barrel of a pen or use the larger barrel of bail making pliers to curve the form into an ear cuff.

Slightly bend the back of the ear cuff inward slightly to grip the lobe.









Add your charm.  These charms come complete with a little lobster claw clip and make it super easy to change out your charm to a different one.  You can make your charm a permanent addition by using chain nose pliers to open the jump ring connecting the clip and the charm and removing the clip.  Tighten the spiral at the bottom of the ear cuff so that it is not as open.  Attach the charm using the jump ring and then close the jump ring.  Personally, I like that I can change these out.


Happy crafting!

LINKS:
DIY Wine Charms by Rebecca Grafton
DIY Gift Packaging by Rebecca Grafton
DIY Skull Necklace by Jennifer Priest
DIY Back To School Ideas by Jennifer Priest
DIY Ideas by Lisa Crone
DIY Handmade Card by Rachel Nielsen
DIY Bookmarks by Rachel Nielsen
DIY Whimsical Ring by Shelly Owen

Tuesday, July 7, 2015

Florida Keepsake Necklace

Of all the souvenirs I receive and pick up in Florida, I think by far my favorite are the little jars of sand and shells.  Why do I like them?  They have so much project potential.

In this tutorial, I will show you how to make a cute, Swarovski crusted, keepsake necklace like the one below. You can customize the project to use any color you choose.  I chose a seaglass theme.


Supplies I Used:
One "Florida" mini-bottle sand and shell keychain souvenir with keychain removed
One 21x10.5 mm Swarovski crystal pendant (6010) in Golden Shadow (SC5152)
SC5152
SC5152
SC5152
Two 7.2mm Swarovski crystal non-hotfix flatbacks (2028) in Mint Alabasater (hard to find)
One 7.2 mm Swarovski crystal non-hotfix flatbacks (2028) in Sand Opal
Four 6mm Swarovski crystal bicones in Sea Glass (47501514)
Four 4mm Swarovski crystal bicones in Sea Glass (47500514)
Two 6mm  heavy gauge jump ring
One 4mm heavy gauge jump ring
Three regular jump rings
Eight silver plated headpins
Swarovski crystal non-hotfix flatback mix in Turquoise and Brown combo (47509569)
Swarovski crystal non-hotfix flatback mix in Crystal (47509526)
Swarovski crystal 4.7mm 2088 Xilion Rose flatbacks in Light Colorado Topaz
36" beige organza ribbon (63800353)
36" large link silver plated copper chain (AJM-ZG-003-00031 available from Walmart)
12" 18 gauge silver plated copper wire
 E-6000 Glue
Singer brand Sew-No-More (available from Walmart)
Singer brand Fray-No-More (available from Walmart)






Tools Used:
Large Bail Making Pliers
Flush Cutters
Chain Nose Pliers (2 pair)
Round Nose Pliers
Large Yarn Needle
Toothpicks

Techniques Required:
Wire Wrapping
Form a Loop
Jump Rings 
Cutting Chain

Skill Level: Intermediate

Craft Time:  About an hour

Instructions:
Put a heavy gauge jump ring through the hole of the Swarovski pendant. Connect the 4mm heavy gauge jump ring to the first jump ring and set aside.  Create 8 Swarovski crystal bicone dangles using headpins and form a loop. Set aside.










Cut 36 inches of large link chain and set aside. Cut 36 inches of organza ribbon and set aside.

Remove cork from mini-bottle. Using a toothpick smear E-6000 to the inside of the keepsake bottle necklace and replace cork.




Form a Loop at the end of the wire. Press the wire against the neck of the bottle and wrap around the neck about three times.

Take the tail of the wire just past the loop and curl backward and thread the tail back through the loop.







Create a spiral with your fingers. Adjust the wraps with round nose pliers to make sure the spiral is smooth










Wrap around the top of the cork two times and pull around and across the top of the cork.  Using the largest barrel of bail making pliers form a triple wrap and trim the wire flush against the cork.


Using a tooth pick, smear glue into the opening in the wraps of wire at the top of the bottle to secure the wire and allow to dry.











Using a toothpick, smear E-6000 onto the bottom of the bottle and one side of the bottle and begin placing on the flatbacks varying the sizes and colors.

















Pick a pattern that is pleasing to you and have fun! Allow to dry.





Open the link of the chain as you would a jump ring - from side to side.

Hook it to the bail of the bottle, and slide into the last link of the other end of the chain.  Close the link.







Open a 6mm jump ring and slide on a 6mm, 4mm bicone, and close the ring. Open another jump ring, thread through the first jump ring and slide one a 6mm and a 4mm bicone.  Repeat until you get to the last jump ring. 


Use a heavy gauge jump ring and thread through the last regular jump ring and slide on the last 6mm bicone dangle, 4mm bicone dangle and the 4mm jump ring of the Swarovski pendant. Attach to the bail of the bottle.

Thread the ribbon onto the large yarn needle. Beginning at the back of the chain, skip the center link and thread through the next skipping every other link.  Make sure to leave a eight inch tail of ribbon.

Do not pull tight or the ribbon could snag on the lengths of the chain.  Pass the needle in the opposite direction of the the tail of the ribbon. 


Smooth out the chain to make sure it isn't bunched up and the ribbon isn't pulled too tight.

Tie a loose overhand knot and then a bow.  Trim the ribbon ends. Treat ends with Fray-No-More and apply a dab of Sew-No-More to the center of the bow.


If you find the "Florida" fading or chipping off, repair with a Sharpie and seal with clear fingernail polish.




Saturday, May 2, 2015

A Little Piece of My Heart - Create Your Style with Swarovski

Cousin Corporation of America (CCA) sent me a lovely box full of Swarovski crystals from their new Create Your Style with Swarovski™ line due to hit A.C. Moore Crafts this month.


These pieces are so versatile you can mix them with so many different things. I love all things Swarovski.  :)  I'm partial I guess.

Well.....I really fell in love with the Swarovski Heliotrope heart pendant that was in the box.  Each time I looked at it, I really felt drawn to pay homage to the Purple Heart medal.  I did my research and found that the ribbon of the medal is purple with white trim and has gold accents.  So I decided to create a lovely "ribbon" using TOHO seed beads in Heliotrope and Matte Opaque White. I wanted gold somewhere, so I decided on a gold chain necklace.



I found these lovely pavé beads with purple crystals from CCA's Jewelry Basics line. I wanted to incorporate them somehow, but the pavé beads didn't quite make it to the final design.

It was a definitely a learning curve since I had never done a decrease Peyote stitch before....How hard could it be, right?  Apparently harder than it looked.  I think I had to rip it apart about four times before it would come out right.  The beauty of using TOHO beads is the large opening that allows for jump rings to slide in even with a ton of thread already in the bead.

After I got the first part done, I had to make a second flap so it would be able to slide on a chain. I stitched it all up along the sides leaving an opening for a thin chain to slide through.

 I chose a thin 14 kt gold plated copper chain from CCA's Elegance Metal Line.  I also put two of the purple crystals from the pave beads at the back connecting to a 14kt gold plated copper heart toggle also from the Elegance Metal line.


I have to say, I am very pleased with the way it turned out.




Wednesday, April 15, 2015

SPARKLE OVER LOAD with tutorial!


Sparkle overload?  Is there even such a thing?  Sounds made up to me......hehehehehhehe.  If diamonds are a girl's best friend, then Swarovski Crystals would be a diamond's best friend.

I love the fire Swarovski has.  They are well known for their quality and brilliance. 

I love it when I get showered in these amazing crystals and crystal pearls.








I recently received an awesome haul of Swarovski crystals courtesy of Cousin Corporation of America (CCA).  Can I say....LOVE LOVE LOVE!  These fiery babies are part of the new "Create Your Style with Swarovski" line rolling out to A.C. Moore the first week of May by Cousin.  This line will be an addition to the already popular Jewelry Basics line from CCA already available at A.C. Moore.

This is very exciting news for CCA. I have to say that I am so proud of Cousin Corporation of America for being part of the prestigious the "Create Your Style with Swarovski" line.  The unparalleled quality of Swarovski meets the high standard of quality and customer service of Cousin Corporation of America.  It's a win-win combination!

I put together this little tutorial for you to enjoy as you wait for the Create Your Style with Swarovski live to become available at your local A.C. Moore.  This dainty bridal bracelet is both delicate and feminine. You can stack it with other bracelets for a little added bling or alone when you want to be a delicate flower.

Create Your Style with Swarovski Bridal Bracelet  


Skill Level: Beginner

Craft Time: Under an hour

Products Used:
Swarovski Xilion Bicone Pearl Combo in Rosaline (47515518) soon to be available from A.C. Moore
Jewelry Basics 59 pc. Starter Pack in Bright Silver (34719157)
Cord Basics Coated Beading Wire (3202102) 
Four 4mm Silver Plated Round Beads  (2950243)
Two Crimp Covers
Two Silver Plated Noodle Beads

Tools Used:
Chain Nose
Flush Cutters
Crimp Tool
Tape Measure
Crimp Cover Closing Pliers (Optional)

Skills Needed:
Stringing
Crimping


Begin my measuring your wrist for size.  Mine will comfortably fit a 7 inch bracelet, but I wanted a loose fit so a 7.5 or 7.75 inch would be perfect.

Measure and cut about 5 inches more of wire than your bracelet size.

Attach a 4mm jump ring (the smallest one in the pack) to the clasp and set aside.

Layout your design to make sure it will fit within the size parameters. You can also do a test string to make sure your design will fit within the length parameters.

I ended up not using the original noodle beads I chose because they were a bit overpowering for the design.  I wanted the crystals are to be the focal point of the bracelet, not the metal.

Here are the new noodle beads














String a crimp tube and a 6 mm jump ring (largest one in the pack) onto the beading wire and push the wire back through the crimp tube forming a loop.  Push the tube back up close to the jump ring giving yourself some space between the tube and the jump ring.

Crimp the tube with your crimping pliers.  (I use crimping pliers for this instead of flat or chain nose because the crimping pliers created a small and stronger crimp.)



Photo from Riogrande.com
Slide a crimp cover over the crimped tube and squeeze closed with either crimp cover closing pliers or your chain nose pliers.






Adding the crimp cover gives you a finished, more professional look as well as protecting your crimp.






Thread on your design and double check your length.  Adjust as needed.

If you have trouble getting your beading wire through the noodle bead, make a bend in the wire with your fingers about a half inch from the end of the wire.  This will help the wire not catch on the edge of the noodle bead.



Thread on another crimp tube and pass the wire through the jump ring of the clasp.  Push the wire back through the tube and slide the tube close to the jump ring leaving some room and crimp.  Cover the tube with a crimp cover and close the cover.

Trim off excess wire.




Wear your bracelet in style!